This site uses cookies, including third parties, in order to improve your experience and to provide services in line with your preferences. By closing this banner, scrolling through this page or by clicking any element its consent to the use of cookies. If you want to learn more or opt out of all or some cookies go to the section

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10

COMPACT PRESS

THE MEASURING OF THE STRENGTH OF CERAMIC FLOOR AND WALL TILES

(An alternative for the method based on the control by means of “PENETRATION EQUIPMENT”)

1. INTRODUCTION

In this leaflet we present a measuring system for the strength of unfired ceramic materials and in

particular pressed tiles.

This technology was developed by the technical ceramics department of the University of Valencia and by the Research Association of the Ceramic Industry in Castellon, Spain.

It is a better alternative for the measuring system for the strength of unfired ceramic material by means of penetration equipment, as the indicated values are not subjective and cannot be influenced by the operator: they are real values as they are based on the measuring of the apparent bulk density.

It is known that the porosity of unfired ceramic pieces, which depends on the type of granules, the grain size and the grain size distribution, the proportion plastic material / defatteners and on the parameters of the pressing action, i.e. pressure, humidity of the powder to be pressed, etc., is a physical property of great importance as it influences the physical properties of the unfired (mechanical resistance) and the fired piece (shrinkage, porosity, mechanical resistance, etc.).

By analyzing the faults that occur most frequently in the manufacture of ceramic floor and wall tiles, it was found that many of these originate from or are influenced by the porosity of the unfired material (black “heart”, a low mechanical resistance, calibre) or by the uneven distribution of the porosity.

From the above, it will be clear that it is necessary to determine the exact value of the porosity during the production process. This can be done by measuring the density or strength and the volume of the pores.

 To enable an effective control of the strength, it is necessary:

a)  to have adeguate testing techniques available with regard to speed of execution of the test.

b)  to determine the maximum period between a fluctuation in the porosity of the unfired material and its distribution over the   interior of the pieces, which is still permissible during the process and which consequently does not bring about significant changes in the quality of the finished product.

c)  to know the entire production process in detail so that, whatever the deviation in the  strength of the unfired piece beyond the preset limits, it can be corrected quickly by adapting the parameters of the process (pressure, humidity) and, in case this would not be possible, adjust the firing in order to reduce the effects of this variation in strength.

2. TESTING METHOD

The most exact testing methods to determine the density in a dry way are based on measuring the volume of the samples (volume of the pores + the real volume of the solid) by displacement of the volume of mercury or by the force which is required to immerse the sample in mercury.

The method of the displacement of the volume of mercury as described by “Stringer” has been partly modified, in order to make it more convenient without changing its accuracy and reliability.

How to proceed:

  • Put a container containing 2 kg mercury on an electronic balance;
  • Weigh the sample to be analyzed;
  • Immerse the sample (making sure that it does not touch the wall of the container) by means of the “COMPACT PRESS” (the sample should be immersed until the mercury reaches the level indication on the immersion system);
  • By immersing the sample in the mercury, one exerts a force which is visible on the display of the balance;

 At this point in time, the volume and the density can be calculated according to the following formulas:

 

 

 

 

 

 

where:                W= weight of the sample (gr.)

                         W3= weight of the sample immersed in the mercury (gr.)                                                  

                         d= density of the mercury (gr/cc.)

 

 

OPTIONAL: Balance


L'AZIENDA

NANNETTI S.r.l. Unipersonale 

L'azienda è il frutto del prolifico lavoro del fondatore Nannetti Antonio Sauro, attivo da oltre 40 anni nell'attività di progettazione e invenzione, spaziando dal design industriale alla produzione meccanica. L'attività si concentra poi nella progettazione e costruzione di forni industriali e forni per ceramica, facendo del laboratorio il target ideale dei propri macchinari.  L'esperienza maturata fino a oggi ha portato l'impresa a lavorare con molte importanti aziende e laboratori sparsi in ogni parte del mondo. Il proprio punto di forza consiste nella customizzazione dei prodotti sulle esigenze del cliente, realizzando un vasta gamma di forni industrialiforni a gradienteforni elettrici, fino alla presse idrauliche da laboratorio, ai flessimetri. La forza della società è costituita dalle persone che la compongono: la loro esperienza e competenza assicurano al cliente una qualità superiore ed un sicuro investimento.